Military vehicles do not evolve in isolation. Their design is shaped by the threats faced by their crews. In the 1940s, the key requirements for a light military vehicle were simplicity, mobility across rough terrain, and the ability to carry troops and equipment. Several decades later, protection against bullets and fragments became increasingly important. In Iraq and Afghanistan, mines and improvised explosive devices became the defining threat. Russia’s full-scale war against Ukraine has added widespread FPV drone attacks and explosives dropped by unmanned aircraft to that list.
This is not a straight line from one vehicle to the next, but a succession of trade-offs: more armor means greater weight; greater weight often reduces mobility; and additional protective structures can restrict visibility, hatch access, and crew operations. Each generation has sought a balance between crew survivability and the vehicle’s ability to perform its mission.
1. The Jeep: Mobility Before Armor
During the Second World War, armies needed a light vehicle that could travel where ordinary trucks could not, carry troops, a radio set or ammunition, and tow a light gun when required. The Willys MB was one answer. Its closely related production counterpart, the Ford GPW, helped meet the demand on a massive scale.
It was an open vehicle with a simple body, low weight, and four-wheel drive. It had no armored crew cell and was not designed to withstand a direct hit. Its advantages were speed, maneuverability, compact dimensions, and the ability to use the terrain for cover. The jeep was not meant to replace armored fighting vehicles; it carried people and equipment to places where heavier vehicles struggled to go.
After the war, the concept of a light multipurpose vehicle lived on in the M38 and M151 MUTT, and later in the HMMWV, widely known as the Humvee. Military vehicles increasingly became platforms for machine guns, grenade launchers, communications equipment, command systems, and medical modules.
2. The Humvee: A Universal Platform That Needed More Armor
The HMMWV entered service with the U.S. Army in the 1980s. It was designed as a family of standardized tactical vehicles capable of replacing several older types. Transport, command, ambulance, and weapons-carrier variants were built on a common platform.
Operations in the 1990s and early 2000s made it clear that the vehicle was being used not only in open maneuver warfare, but also in urban areas, on roads vulnerable to ambushes, and under small-arms fire. Armored versions and add-on protection kits followed. However, adding armor did not turn the Humvee into a vehicle specifically engineered to withstand a powerful blast beneath its floor.
Armored doors and panels offered protection against bullets and fragments, but a mine or IED blast transmitted a powerful impulse through the vehicle structure. The force could deform the floor, damage vehicle components, and cause severe crew injuries even when the armor itself was not penetrated. This exposed the limits of upgrading the original design.
3. Mine Protection: Lessons from Southern Africa
The idea of a dedicated mine-protected vehicle emerged long before U.S. forces began deploying MRAPs on a large scale. Experience in South Africa and Rhodesia played an important role in developing the concept, as mines and attacks on vehicle convoys were persistent threats. Engineers looked beyond simply adding thicker armor plates: they sought to change the vehicle’s geometry.
One characteristic solution was the V-shaped hull. Its geometry was intended to deflect some of the blast energy outward rather than channel it directly into the floor and crew compartment. High ground clearance increased the distance between the explosion and the people inside. Seat mounts, floor construction, fuel-tank placement, and many other details also became critical.
Early vehicles in this field included the Buffel and Casspir. Developed in South Africa in the late 1970s, the Casspir featured a distinctive high body and V-shaped lower hull. Its design became a clear example of how the requirement for mine protection can determine a vehicle’s entire appearance.
A V-shaped hull does not make a vehicle invulnerable. The outcome depends on the charge’s size and type, the point of detonation, the hull design, wheels and suspension, and the crew-station layout. Nevertheless, changing the hull geometry marked an important shift from conventional armor to purpose-built mine protection.
4. Iraq and Afghanistan: MRAP Becomes an Urgent Requirement
After the 2003 invasion of Iraq, U.S. and coalition forces faced widespread use of improvised explosive devices (IEDs). They were placed along roads, in vehicles, on road shoulders, and at locations regularly used by patrols and convoys. The blasts damaged vehicles and inflicted devastating injuries on the crews inside them.
The need for a different type of vehicle became so urgent that in February 2007 the U.S. Department of Defense launched a major MRAP program - Mine Resistant Ambush Protected. A July 2008 report by the U.S. Government Accountability Office (GAO) stated that, at the time, approximately 75 percent of U.S. casualties in operations in Iraq and Afghanistan were associated with IEDs. More than $22 billion had already been allocated toward the planned purchase of over 15,000 MRAP vehicles.
The program moved at an extraordinary pace. The Pentagon brought in several manufacturers, drew on existing commercial designs, and carried out testing, production, and fielding in parallel. This rapidly increased the number of protected vehicles, but also created challenges involving maintenance, spare parts, mobility, and the operation of multiple different models.
The MRAP family included vehicles from different manufacturers and in a range of configurations. Among the best known were the Cougar, International MaxxPro, RG-31, RG-33, Caiman, and Buffalo. Some carried troops, others escorted convoys, cleared routes, or performed specialized missions. Their common priority was to improve the crew’s chances of surviving a blast or ambush.
More on the procurement pace, design requirements, and challenges of the program can be found in the U.S. Government Accountability Office report on the accelerated acquisition of MRAP vehicles.
5. Why MRAP Was Not a Universal Solution
Greater protection came at a cost. Large MRAPs were heavy and tall, and were not always well suited to narrow roads, bridges, or difficult terrain. They consumed more fuel, required specialized maintenance, and placed additional demands on logistics. A vehicle that could withstand a roadside blast might prove awkward on mountain patrol routes or when maneuvering through dense urban areas.
This did not mean the MRAP concept was flawed. It addressed a specific threat: mines and IEDs. But Afghanistan showed that protection had to be balanced with cross-country mobility. Mountain roads, narrow routes, and uneven ground called for a different balance between armor, weight, and the running gear.
6. The M-ATV: Restoring Mobility Without Giving Up Mine Protection
In 2009, the U.S. military set out a new requirement: a vehicle that retained MRAP-level protection but performed better over difficult terrain. The result was the M-ATV - Mine Resistant Ambush Protected All-Terrain Vehicle. It was not simply a “smaller MRAP,” but a response to a different set of operating conditions.
In June 2009, Oshkosh received a contract worth approximately $1.05 billion for the first batch of 2,244 vehicles. The first M-ATVs arrived in Afghanistan that autumn. The vehicle featured a V-shaped armored hull, independent suspension, and a configuration designed for difficult terrain. According to an Army publication, an M-ATV with standard equipment and fuel weighed about 25,000 pounds, while some larger MRAPs could weigh nearly 60,000 pounds.
The difference in weight helps explain the logic behind this new generation. The M-ATV retained mine protection while seeking to restore the ability to move through terrain that challenged heavier MRAPs. An Army article on the arrival of the first M-ATVs in Afghanistan describes the requirement and compares the vehicle with the larger MaxxPro Dash.
This illustrates a recurring principle of military vehicle design: improving one characteristic does not eliminate the need for the others. Protection, cross-country mobility, speed, payload, range, and maintainability all have to work together.
7. The Ukrainian Experience: Armor No Longer Guarantees Safety
Russia’s full-scale war against Ukraine has changed the conditions in which armored vehicles operate. FPV drones, reconnaissance UAVs, and bomb-dropping drones have made not only exposed roads dangerous, but also stopping points, shelters, repair areas, and logistics routes. An attacker no longer has to penetrate a vehicle’s frontal armor or plant an explosive beneath its wheels to put it out of action.
An FPV drone can target the roof, engine compartment, hatches, joints between armor plates, or other vulnerable areas. A drone dropping a munition presents a different problem: the explosive can enter an open hatch or hit a surface where the vehicle’s standard armor offers insufficient protection. Even if the hull withstands fragments, a nearby explosion can damage optics, antennas, communications equipment, the running gear, or other critical components.
Fiber-optic FPV drones add another complication. They transmit control signals through a thin cable rather than a conventional radio link, so traditional radio-frequency jamming cannot be a universal countermeasure. Ukrainian researchers examine this challenge in “Countering FPV Drones: Insights from Ukraine’s Combat Experience,” published in the journal Advances in Military Technology in 2025.
8. “Cope Cages,” Mesh, and Chains: Improvised Protection for a New Generation of Threats
One of the most visible responses to the FPV threat has been the addition of external protective structures. Metal frames, grilles, mesh screens, and canopies have appeared on armored vehicles and tanks. In everyday Ukrainian usage, these structures are often called “mangals”; in English, similar arrangements are commonly referred to as cope cages or anti-drone cages. Their purpose is to create a physical barrier between the drone and the vehicle, alter the point of contact, or prevent a munition from striking the main armor directly.
The solutions may look crude, but the logic is straightforward: if electronic warfare cannot reliably stop a drone, a physical obstacle may prevent it from reaching the hull. Mesh and grilles may snag propellers, disrupt the drone’s approach, create stand-off distance from the main armor, or affect how a warhead functions. The outcome, however, depends on the munition type, angle and speed of approach, barrier design, and where it is installed.
Chains, rubber elements, and other hanging components have also appeared on some vehicles as additional field-expedient protection. They should not be mistaken for a standardized system with guaranteed results. These are varied local adaptations that may help in specific circumstances, but they do not replace a tested, integrated protection suite.
There are practical drawbacks as well. A frame increases the vehicle’s dimensions and can interfere with hatch operation, crew entry and exit, visibility, or weapon systems. Mesh can be damaged, sag, or ice over. A structure may need repair or replacement after a single hit. Any add-on protection therefore has to be adapted to the specific vehicle and its mission.
9. From Passive Protection to Layered Countermeasures
An external frame is only one layer of protection. Modern counter-drone defense is increasingly a system combining threat detection, crew warning, electronic warfare, physical barriers, and active interception systems.
- Detection. Radio-frequency detectors, optical sensors, and acoustic systems can help identify a drone or its operator before the crew sees the aircraft itself.
- Electronic warfare. EW systems can disrupt control or navigation links used by some drones, but their effectiveness depends on the specific system. Fiber-optic control links change the equation.
- Passive physical barriers. Mesh, grilles, frames, and canopies can reduce the vulnerability of particular parts of a vehicle, although they do not provide complete coverage.
- Active protection. One promising direction is systems that detect an incoming drone and physically intercept it, including through dedicated net-based or other countermeasures.
- Movement and tactics. Concealment, dispersion, and changes to routes and movement times remain important ways to reduce risk.
The key point is that there is no universal “anti-drone cage.” Protection must account for threats from different directions, preserve the crew’s ability to leave the vehicle quickly, and avoid critically obstructing visibility or vehicle operation. Effective protection against aerial threats is no longer just a property of the armored hull; it is an integrated system involving the vehicle, its crew, detection equipment, and counter-drone units.
A Military Vehicle Is More Than Its Armor
Several generations of military vehicles separate the Willys MB from the MRAP and M-ATV. At first, designers aimed to give armies a simple vehicle with good cross-country mobility. Later came the need to protect crews from bullets and fragments. The experience of mine warfare drove changes to hull geometry, suspension, and crew layout. Today, armored vehicles are being fitted with additional structures and systems intended to counter drones.
This evolution does not end with the arrival of another model. Threats change faster than the full development cycle of a new vehicle, forcing militaries and engineers to keep adapting equipment already in service. In modern warfare, crew survival depends not only on armor thickness, but also on how quickly a vehicle and its equipment can adapt to a changing battlefield.
There is another dimension to life inside an armored vehicle: personal belongings, unit insignia, and reminders of the places where the crew serves. That is why patches often become part of a military vehicle’s interior. Explore the Raccoon Merch collection of PVC patches, including designs inspired by FPV operations, military units, and the Ukrainian cities defended by service members.
Toyota at War: The History of the Hilux and Land Cruiser in Armed Conflicts
Pickups at War: How a Versatile Vehicle Became Essential to Modern Armies
Electronic Intelligence (ELINT): How It Works and What It Can Reveal from the Radio Spectrum
Electronic Warfare (EW): How It Works, Its Capabilities and Limitations
Structure of Ukraine’s Armed Forces and Defence Forces: From Squad to Corps
The Evolution of FPV on the Frontline: How a Civilian Hobby Reshaped Modern Warfare
What to Give a Commander or Officer - Gift Ideas for a Military Service Member
Military Patches: How a Small Patch Became a Symbol of Military Culture
What to Gift a Soldier: 15 Meaningful Gift Ideas They'll Truly Appreciate